Ohmify Starter Kit + ebook

Build Blinking Lights, Alarms and Sirens

A box of real components, plus my step-by-step ebook with nine fun experiments. No soldering, no experience needed.

The Ohmify component kit box
What you'll build

Nine Experiments, Each One Building on the Last

The ebook Fun Circuit Experiments With Light and Sound takes you from a single blinking LED to a siren that runs all by itself. Every experiment has a schematic, a drawing of exactly where each part goes on the breadboard, and a simple explanation of how it works.

The cover of the ebook Fun Circuit Experiments With Light and Sound
  1. Make an LED blink
    Build an oscillator, the little circuit behind every experiment in the book.
  2. Change the speed with a resistor
    Swap resistors and watch the blinking speed up or slow down.
  3. Change the speed with a capacitor
    See how a bigger or smaller capacitor changes the rhythm.
  4. Add a speed knob
    Use a potentiometer to adjust the blinking as you go.
  5. Make five LEDs blink
    Use a transistor to power more LEDs than the chip can on its own.
  6. Make sound
    Speed up the blinking and turn it into a tone with a buzzer.
  7. Build an alarm
    Combine two oscillators to switch the sound on and off.
  8. Build a siren with a button
    Push the button to switch between two tones.
  9. Build an automatic siren
    Let a second oscillator push the button for you.
“Super fun experiments to get back into electronics. Highly recommended!”
What's in the box

Real Components You'll Find in Any Electronics Shop

No special modules or proprietary boards. Everything in the kit is a standard component, so what you learn works with parts from anywhere.

Breadboard
Breadboard
1 x solderless breadboard (400 points), for building circuits without soldering.
Breadboard wires
Breadboard wires
20 x male-to-male DuPont wires, to connect rows on the breadboard.
9V battery clip
9V battery clip
1 x battery connector, to power your circuits from a 9V battery.
Resistors
Resistors
4 each of the most common values, including 100 Ω, 470 Ω, 1 kΩ, 10 kΩ, 47 kΩ and 100 kΩ.
Potentiometer
Potentiometer
1 x 100 kΩ potentiometer, a resistor you adjust with a knob.
Ceramic capacitors
Ceramic capacitors
1 x 10 nF and 2 x 0.1 µF.
Electrolytic capacitors
Electrolytic capacitors
1 x 4.7 µF, 2 x 10 µF, 2 x 100 µF and 1 x 1000 µF.
Transistors
Transistors
2 x NPN (BC547) and 1 x PNP (BC557).
LEDs
LEDs
10 x red LEDs.
Photoresistor
Photoresistor
1 x light-dependent resistor, to make circuits that react to light.
Buzzer
Buzzer
1 x passive buzzer, to make sounds.
555 timer
555 timer
1 x 555 timer chip, for blinkers, tones and timers.
4017 decade counter
4017 decade counter
1 x CD4017 chip, for running lights and sequences.
Schmitt trigger inverter
Schmitt trigger inverter
1 x CD40106 chip, for oscillators and clean signals.
Pushbuttons
Pushbuttons
4 x pushbuttons, to control your circuits.

The full list

1 x 9V Battery Connector
1 x Solderless Breadboard (400-Point)
20 x Male to Male DuPont Wire
4 x Resistor 100 Ω
4 x Resistor 470 Ω
4 x Resistor 1 kΩ
4 x Resistor 10 kΩ
4 x Resistor 47 kΩ
4 x Resistor 100 kΩ
1 x Potentiometer 100 kΩ
1 x Capacitor 10 nF
2 x Capacitor 0.1 µF
1 x Capacitor 4.7 µF
2 x Capacitor 10 µF
2 x Capacitor 100 µF
1 x Capacitor 1000 µF
2 x Transistor NPN (BC547)
1 x Transistor PNP (BC557)
10 x LED (Red)
1 x Photoresistor (Light: ~10 kΩ, Dark: ~1 MΩ)
1 x Buzzer (Passive, Transducer)
1 x Hex Schmitt Trigger Inverter IC (CD40106BE)
1 x 555 Timer IC
1 x 4017 Decade Counter
4 x Pushbutton

Not sure which part is which? See the component identification page.

Get the Kit + Ebook

Everything you need for all nine experiments, in one box.

Starter Kit + Ebook
$49
one-time payment, free US shipping
Every component you need for all nine experiments
The ebook Fun Circuit Experiments With Light and Sound (PDF), yours to download right away
Standard parts: replace or add to them from any shop
Free shipping within the US, from our warehouse in Nevada
Outside the US?

The kit only ships within the US for now. Get the ebook on its own and buy the parts locally. Every experiment has a parts list, and all the parts are common ones you can find in most stores that sell electronic components.

Get the ebook – $19
Shipping

Free Shipping Within the US

We pack your kit and send it from our warehouse in Nevada, and you’ll get a tracking code by email within a couple of days. The ebook is yours to download right after you buy, so you can start reading while the kit is on its way.

For now, the kit only ships within the US.

FAQ

Your Questions Answered

Ready to Make Your First Light Blink?